Fire Retardants Texas - Fort Worth/Dallas based

INTERIOR FIRE RETARDANT
COATING or SPRAY
FOR ALL INTERIOR WOOD
PLYWOOD ● LUMBER ● TIMBER

  CLASSIFIED
FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING

Surface	Douglas fir
Flame spread	20
Smoke developed	90
Number of preliminary coats	None
Rate per coat (ft2/gal)	--
Number of fire retardant coats	3
Rate per coat (ft2/gal)	500
Number of overcoats	None
Rate per coat (ft2/gal)	--
Flash point of liquid coating:
Fire retarding coating - closed cup,	no flash

FIRE POLY 75 I TECHNICAL DATA

ASTM E-84 CLASS A    UL 723 TYPE 1

PRODUCT DESCRIPTION:    Aqueous Based Resin

	Product	Analysis
Total Solids	46%	PH	2.5-2.8
Weight per gallon	10.7lbs	Flash point	Non-Flammable
Specific gravity	1.33	Color	Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability	Non-Volatile	Solvents	Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus	Excellent Resistance	Bacterial	Good Resistance
Linear shrinkage	None	Moisture Absorption	None
Corrosive	Mildly	Toxic	None (when dry)
Insects, rodents, aspergilli And other types of molds	Excellent resistance	Termites	Excellent resistance
Preservative for wood	Good	Scrubability	1000 cycles

RECOMMENDED USE: Interior Class A Rating (Flame spread less than 25)

FLAME SAFE FIRE POLY 75 I is a fire retardant and wood preservative coating. It can be used on any type of wood, porous, or non-porous materials, such as:

Yellow pine	Redwood	Cedar
Douglas Fir	Plywood	Wall Coverings
Wafer Board (OSB)	Particle Board	Corrugated Board

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.

QUICK REFERENCE FOR APPLYING FIRE POLY 75 I

MATERIAL	APPLICATION	COVERAGE
Interior wood any type of wood such as: Yellow Pine, Douglas fir, Cedar, and redwood	Treat before, during or after construction. Be sure surface is clean and dry before treating. Apply with sprayer head held at 8 to 12 inches from surface. Apply with brush or roller. Treat all surface areas where possible Do not expose treated area to moisture for 24 hours.	Apply three (3) coats at 500 sq. ft. per coat with the final coverage rate of 166.3 sq. ft. per gallon

INTERIOR PLYWOOD ● LUMBER ● TIMBER ● WOOD PRODUCTS

            All surfaces to be treated must be clean and dry. Fire Poly 75 I is water-based, clear liquid that becomes insoluble when dry. Fire Poly 75 I also acts as a preservative, and water proofing agent. If over coating is intended, Fire Poly 75 I is an excellent surface primer for use under latex paints.

DO NOT DILUTE OR MIX FIRE POLY 75 I WITH ANY OTHER PRODUCTS.

            Avoid wasteful runs and dripping. It should be noted that unlike some products, materials treated with Fire Poly 75-I require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.

           Structures under construction can be made fire resistant. As soon as the surface is enclosed, spray all exposed interior surfaces (studs, trusses, sub floor, joists, the interior of outside walls, etc.) with Fire Poly 75 I. This will provide the structure with a long-term fire retardant protection.

            Fire Poly 75 I when applied according to the manufacturer’s specifications is the most effective fire retardant coating available.

CAUTION:

          Product must not freeze. It must not be thinned or diluted.

OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.

CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

 

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.

          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).

SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.